How do you control the speed of a RC helicopter?

Controlling the speed of a remote control (RC) helicopter is an important part of flying it safely and effectively. The speed of a RC helicopter is controlled by the throttle, which is the lever on the transmitter (remote control) that is used to adjust the power of the motor. The throttle is usually located on the right side of the transmitter and is usually the topmost lever.

When the throttle is pushed forward, the motor speed increases, and when it is pulled back, the motor speed decreases. The throttle is usually calibrated in percentages, so pushing the throttle forward to the 50% mark will give the helicopter half of its maximum speed.

In addition to the throttle, the pitch of the blades also affects the speed of the helicopter. The pitch of the blades is adjusted by the pitch control, which is usually the lever located directly below the throttle. When the pitch is increased, the blades move faster, which increases the speed of the helicopter. When the pitch is decreased, the blades move slower, which decreases the speed of the helicopter.

The speed of the helicopter can also be affected by the weight of the helicopter. Heavier helicopters require more power to reach the same speed as lighter helicopters. This means that if you want to increase the speed of a heavier helicopter, you will need to increase the throttle and pitch more than you would for a lighter helicopter.

Finally, the speed of the helicopter can also be affected by the wind. If the wind is blowing in the same direction as the helicopter, it will help the helicopter to move faster. If the wind is blowing in the opposite direction, it will slow the helicopter down.

In summary, the speed of a RC helicopter is controlled by the throttle, pitch, weight, and wind. By adjusting the throttle and pitch, you can increase or decrease the speed of the helicopter. The weight of the helicopter and the wind can also affect the speed of the helicopter. With practice, you can learn to control the speed of your RC helicopter and fly it safely and effectively.

Was this article useful? 👍 0 👎 0 👀 0 Rating: Posted by: 👨 Robert R. Dinh

Add new comment/question

Comments / Question

👤 💬

What are the recommended speed settings for different types of RC helicopters?

👨 📜

1. Micro/Indoor Helicopters:
• Tail Rotor Speed: 5,000 - 6,000 RPM
• Main Rotor Speed: 2,500 - 3,500 RPM
2. Beginner/Trainer Helicopters:
• Tail Rotor Speed: 8,000 - 10,000 RPM
• Main Rotor Speed: 4,000 - 5,000 RPM
3. Intermediate/Advanced Helicopters:
• Tail Rotor Speed: 10,000 - 12,000 RPM
• Main Rotor Speed: 5,000 - 6,000 RPM
4. 3D/Competition Helicopters:
• Tail Rotor Speed: 12,000 - 14,000 RPM
• Main Rotor Speed: 6,000 - 8,000 RPM

👤 💬

How can you make sure to maintain a constant speed when flying a RC helicopter?

👨 📜

1. Start with a slower speed and gradually increase it.
2. Use a gyroscope to keep the helicopter stable.
3. Make sure the battery is fully charged and has enough power to maintain the desired speed.
4. Make sure the propeller is balanced.
5. Use a throttle curve to adjust the speed.
6. Use a remote control transmitter with a proportional control system.
7. Practice hovering and flying at a constant speed.
8. Avoid sudden changes in direction or speed.

👤 💬

Are there any software programs that can be used to control the speed of a RC helicopter?

👨 📜

Yes, there are a number of software programs that can be used to control the speed of a RC helicopter. These include programs such as MultiWii, Arduino, and KKmulticopter. These programs allow users to adjust the speed of their RC helicopter, as well as other parameters such as yaw, pitch, and roll.

👤 💬

Are there any specific hardware components that can be used to adjust the speed of a RC helicopter?

👨 📜

Yes, there are several hardware components that can be used to adjust the speed of a RC helicopter. These include brushless motors, electronic speed controllers (ESCs), and propellers. Brushless motors are the most common type of motor used in RC helicopters and are capable of producing a wide range of speeds. ESCs are used to control the speed of the motor and can be adjusted to increase or decrease the speed of the helicopter. Propellers are also used to adjust the speed of the helicopter and can be changed to different sizes and pitch angles to increase or decrease the speed.

👤 💬

What are some methods you can use to regulate the speed of a RC helicopter?

👨 📜

1. Adjust the throttle curve on the transmitter.
2. Change the size of the main rotor blades.
3. Adjust the pitch of the main rotor blades.
4. Change the size of the tail rotor blades.
5. Adjust the weight of the helicopter.
6. Change the gear ratio of the drive system.
7. Install an electronic speed controller (ESC).
8. Install a governor system.
9. Install a gyro system.
10. Install a flybarless system.